mbgetesf
Section:  MB-System 5.0  (1)
Updated:  3 June 2013 
Index


 
NAME

mbgetesf - Extract swath bathymetry data flags into an edit save file.

 
VERSION

Version 5.0

 
SYNOPSIS

mbgetesf [-Fformat -Iinfile -Mmode -Oesffile -V -H]

 
DESCRIPTION

Swath bathymetry data is typically edited either with interactive
tools such as mbedit or automatic filters such as mbclean.
The beams which are deemed "bad" are flagged, and the flags are
output to an "edit save file", which can be applied to data
later by mbprocess.
Occasionally, the need arises to translate data
flagging information from one file to another which represents a
different version of the same dataset.  In particular, it may happen
that editing has been done on a data format which does not support
all of the original data stream (e.g. the edmb Hydrosweep format 22,
which does not contain travel times or amplitudes), but the user now
wishes to work with the complete data stream without having to redo
the editing process.

The utility mbgetesf allows the user to extract
the flagging information in the form of an
"edit save file" like those generated by mbedit and
mbclean. These edits can be applied to data later
using mbprocess. If the edit save file is named
properly (an ".esf" suffix added to the input swath file
name), the edits can automatically be loaded into mbedit or
mbclean.

The user can extract edit events from only the flagged beams (-M1),
or can extract edit events specifying null and flagged beams (-M2)
and all (good, flagged, and null) beams (-M3). The latter cases are necessary only if
previous editing has involved nulling beams that were
originally classified as good or unflagging beams that were
originally flagged.

The default input is from stdin, and the default output is
to standard out.

 
AUTHORSHIP

David W. Caress (caress@mbari.org)




  Monterey Bay Aquarium Research Institute



Dale N. Chayes (dale@ldeo.columbia.edu)




  Lamont-Doherty Earth Observatory

 
OPTIONS


-F


format



Sets the format for the input and output swath data using
MBIO integer format identifiers.
These utilities uses the MBIO library and will read any swath data
format supported by MBIO. A list of the swath data formats
currently supported by MBIO and their identifier values
is given in the MBIO manual page.
-H


This "help" flag causes the program to print out a description
of its operation and then exit immediately.
-I


infile



Data file from which the input data will be read. If
no input file is specified, the input will be read
from stdin. Default: infile = stdin.
-M


mode



Specifies which beam flag values are output as edit events.
If mode = 1, then only flagged beams are output. If
mode = 2, then flagged and null beams are output. If
mode = 3, then an edit event will be output for every
beam, including those that are "good" (neither flagged nor
null). Default: mode = 1.
-O


esffile



Specifies output edit save file to which the
edit events will be written. If
no edit save file is specified, the output will be written
to stdout. Default: esffile = stdout.
-V


Normally, mbgetesf works "silently" without outputting
anything to the stderr stream.  If the
-V flag is given, then mbgetesf works in a "verbose" mode and
outputs the program version being used and all error status messages.


 
EXAMPLES

Suppose one has an edmb format (MBIO format id 22) Hydrosweep
file called hs_ew9103_143.mb22 which has been edited using older
versions of mbedit so that no edit save file was generated.
Further suppose that one's thesis advisor
suggests that the bathymetry would be better if it were recalculated
from travel times using a new water velocity model, requiring that
the raw Hydrosweep data (originally collected in format 21 but
recently translated to format 24) in the file hs_ew9103_143.mb24
be used. First extract the edit events in the form of
a edit save file from the edited edmb file:

        mbgetesf -F22 -Ihs_ew9103_143.mb22              -Ohs_ew9103_143.mb24.esf -V




Note that the edit save file has been given the name of the
second swath file with ".esf" appended. This naming convention
is the same as if mbedit or mbclean had been
run on hs_ew9103_143.mb24. Now, running either mbedit or mbclean
will automatically load the edit events as a starting point
for editing or filtering.
To simply apply the extracted edit events to the swath bathymetry,
first use mbset to enable applying the edits in the
mbprocess parameter file, and then run mbprocess
to actually apply the edits and generate a processed output
swath file:

        mbset -Ihs_ew9103_143.mb24              -PEDITSAVEMODE:1                -PEDITSAVEFILE:hs_ew9103_143.mb24.esf  -V


        mbprocess -Ihs_ew9103_143.mb24 -V




The output swath file will be named hs_ew9103_143p.mb24.

 
SEE ALSO

mbsystem(1), mbedit(1), mbclean(1),
mbset(1), mbprocess(1).

 
BUGS

Let us know.



 
Index

NAME

VERSION

SYNOPSIS

DESCRIPTION

AUTHORSHIP

OPTIONS

EXAMPLES

SEE ALSO

BUGS

Return to list of MB-System manual pages...

Back to MB-System Home Page...